POOSHESH STEELPERGAS
فا

ENAW-AlMg2Mn0.3

Wrought Aluminum Alloys

OverviewChemical CompositionMechanical PropertiesPhysical PropertiesOther Properties

Property Overview

Density-g/cm³
Elastic ModulusUnknown
Tensile Strength160MPa
Yield Strength60MPa
Brinell Hardness45HB
Maximum Service TemperatureUnknown
Weight Calculator

Chemical Composition

MN
ENAW-AlMg2Mn0.3 ( ENAW-5251 ) Aluminium - 5000 series ( Magnesium Mg is major alloying element ) Chemical composition. Equivalents of ENAW-AlMg2Mn0.3 ( ENAW-5251 ). Standards.1 Mechanical Properties. Hardness%

Mechanical

A - Min. elongation Lo = 50mm (%) (F) (H112)
14
A - Min. elongation Lo = 50mm (%) (H14)
2-5
A - Min. elongation Lo = 50mm (%) (O) (H111)
15
A - Min. elongation at fracture (%) (F) (H112)
16
A - Min. elongation at fracture (%) (O) (H111)
17
R p0.2 0.2% proof strength (MPa) (F) (H112)
60
R p0.2 0.2% proof strength (MPa) (H14)
170
R p0.2 0.2% proof strength (MPa) (O) (H111)
60
Rm - Tensile strength (MPa) (F) (H112)
160
Rm - Tensile strength (MPa) (H14)
210-250
Rm - Tensile strength (MPa) (O) (H111)
160-220

Hardness

Brinell hardness (HBW): (F) (H112)
45
Brinell hardness (HBW): (H14)
64
Brinell hardness (HBW): (O) (H111)
45
Registered Designations & Aliases
ENAW-5251ENAW-AlMg2Mn0.3
Standards

EN 12392 EN 12392: 2000 Aluminium and aluminium alloys. Wrought products. Special requirements for products intended for the production of pressure equipment

EN 1301-2 EN 1301-2: 1997 Aluminium and aluminium alloys. Drawn wire. Mechanical properties

EN 1396 EN 1396: 2007 Aluminium and aluminium alloys. Coil coated sheet and strip for general applications. Specifications

EN 1592-2 EN 1592-2: 1998 Aluminium and aluminium alloys. HF seam welded tubes. Mechanical properties

EN 1715-3 EN 1715-3: 2008 Aluminium and aluminium alloys. Drawing stock. Specific requirements for mechanical uses (excluding welding)

EN 485-2 EN 485-2: 2008 Aluminium and aluminium alloys. Sheet, strip and plate. Mechanical properties

EN 570 EN 570: 2007 Aluminium and aluminium alloys. Impact extrusion slugs obtained from wrought products. Specification

EN 573-3 EN 573-3: 2009 Aluminium and aluminium alloys. Chemical composition and form of wrought products. Chemical composition and form of products

EN 754-2 EN 754-2: 2008 Aluminium and aluminium alloys. Cold drawn rod/bar and tube. Mechanical properties

EN 755-2 EN 755-2: 2008 Aluminium and aluminium alloys. Extruded rod/bar, tube and profiles. Mechanical properties

EN 851 EN 851: 1996 Aluminium and aluminium alloys. Circle and circle stock for the production of culinary utensils. Specifications

EN 941 EN 941: 1996 Aluminium and aluminium alloys. Circle and circle stock for general applications. Specifications